Matala kuormaaja

Fliegl ZTS 200

Customized Transport Solution
Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs.

Further Information
Chassis
Steel welded construction
Turntable with robust ball bearing race, storage box recessed in the turntable extension
Foldable rear support
Chocks with holder
Aluminum side impact protection
Splash guard at the rear over the entire width
Quarter panel fenders in front of the 1st axle
Spare wheel holder for 1 spare wheel, with wheel fastening kit
Spare wheel, same brand as the standard tires, steel rim
Plastic toolbox, with insert, w=620/h=360/d=440 mm, lockable with a padlock. (Lock not included)
Tie-down points for low-loader
3 pairs of tie-down points, 10 tons each, integrated in the floor at the front
6 pairs of tie-down eyes recessed in the upper and side parts of the outer frame, 10 tons each
1 x at the neck area, the rest spaced out with a maximum distance of 1200 mm
1 x rear slope
5 pairs of ring tie-down points recessed in the outer frame, 5 tons each (can be converted to stake pockets)
Coupling device, trailer, turntable
Drawbar with tested 40 mm drawbar eye
Axles and Suspension
SAF drum brake axles
Axle/chassis laser-aligned, reducing tire wear and fuel consumption
Parabolic suspension with maintenance-free steel-rubber mounting
Wheels and Tires
235 / 75 R 17,5
According to the manufacturer's choice
Steel rims in twin arrangement, factory silver
Braking System
2-line compressed air braking system
Spring brake parking brake
2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle
ABS and ALB, with ABS plug at the front, with connecting cable
Voltage converter for 12/24 Volt operation
Note! A 7-pin socket, 12 Volt, is required on the tractor/tow vehicle! (Required in conjunction with the voltage converter for electrical system!)
Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS!
Electrical System
24 Volt, multi-chamber lights, yellow LED lighting on the sides
2 white/red position lights at the rear
2 white position lights at the front
Additional LED work lights at the rear, switched on via reversing light
2 x 7-pin fail-safe plugs at the front, with connecting cable
1 x 7-pin agricultural plug
Lajdpfx Aei Ri Nxoa Djc
Voltage converter 12/24 Volt (only for electrical system, not for ABS/EBS)
Floor
Front area: steel floor
Then with 70 mm softwood floor, steel/non-slip sheet metal covering in the wheel arch area
Rear slope with 70 mm softwood floor
Low-loader platform including rear slope 8,200 mm
Loading Ramps
Steel ramps 2,800 mm long, 750 mm wide, laterally movable
Covered with wood
With spring-assisted support
Operating Instructions
A special permit is required for an axle load of 10,000 kg. The permit must be applied for separately in each federal state; a guarantee for a 20-ton gross vehicle weight must not be given by the legislator. Customer risk.
Country of Registration / Signs
Country of registration: Germany
With DEKRA inspection and certificate (according to §13 EG - FGV)
24/7 Service Hotline
Prepared for license plate holder, two-line
Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear
Paintwork
Frame DB 7350 Novagrau
10-year warranty against rust
Drawbar galvanized or black, according to manufacturer's choice
Loading ramps hot-dip galvanized
Note: Archive images!

Ilmoitus on käännetty automaattisesti. Käännösvirheitä saattaa esiintyä.