Matala lavetti perävaunuFliegl
2-Achs Tieflade Anhänger ZTS 200 Spezial
Matala lavetti perävaunu
Fliegl
2-Achs Tieflade Anhänger ZTS 200 Spezial
EXW VB alv 0% (veroton)
43 900 €
(52 241 € bruttomassa)
Kunto
Käytetty
Sijainti
Triptis 

Perustiedot
Hinta ja sijainti
EXW VB alv 0% (veroton)
43 900 €
(52 241 € bruttomassa)
- Sijainti:
- Oberpöllnitzer Straße 8, 07819 Triptis, Deutschland

Soita
Tekniset tiedot
- Omamassa:
- 6 200 kg
- Maksimi kuormauspaino:
- 11 800 kg
- Kokonaispaino:
- 18 000 kg
- Akselikokoonpano:
- 2 akselia
- Ensirekisteröinti:
- 05/2018
- Kuormatilan korkeus:
- 200 mm
- Kokonaispituus:
- 11 600 mm
- Kokonaisleveys:
- 2 550 mm
- Jousitus:
- ilma
- Renkaan koko:
- 235/75 R17,5"
- Väri:
- punainen
Tarjouksen tiedot
- Ilmoituksen tunnus:
- A826-55-99
- Viitenumero:
- 46253
- Päivitys:
- viimeksi 06.06.2026
Kuvaus
Additional information
Chassis: Steel welded construction, double-curved with a low-bed section in front of and behind the axle unit, the low-bed section is angled for easier access, turntable with robust ball bearing race, foldable rear support, chocks, side impact protection, quarter-panel fenders
Lashing points: above the front axle: 2 pairs of ring lashing points, each 5 tons, at the front on the low-bed section / rear axle: 6 pairs of lashing points on the side in the low-bed section, each 8 tons. 6 pairs of lashing points, each 5 tons, between the longitudinal beams, a pair of pocket recesses embedded in the outer frame, internally 70 x 40 mm, or instead of pocket recesses, 5-ton ring lashing points embedded in the floor
Drawbar: tested 40 mm drawbar eye
Axles: BPW drum brake axles
Braking system: 2-line pneumatic braking system, spring-loaded parking brake, 2 non-interchangeable coupling heads at the front
Electrical system: 24 volts, multi-chamber lights, yellow side lighting, 2 white position lights at the front
2 white/red outline marker lights at the rear, rotating beacon with bracket, pair of illuminated and extendable warning signs up to 3,000 mm, 2 x 7-pole non-interchangeable connectors at the front
Floor: curved section at the front with steel/diamond-plate covering, storage compartment embedded in the access ramp to the curved section, driving lane area and in the center between the beams with steel/diamond-plate covering, rear slope with 70 mm softwood floor, low-bed platform including rear slope 5900 mm
Ramps: mounting rail for aluminum ramps over the entire width, as a U-profile over the entire width
Pair of aluminum ramps 800 mm long, approx. 400 mm wide, load capacity per pair 14,000 kg
Storage compartment for ramps between the beams
Approval: contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear
Lrsdpfx Aei Ri N Uslgen
Ilmoitus on käännetty automaattisesti. Käännösvirheitä saattaa esiintyä.
Chassis: Steel welded construction, double-curved with a low-bed section in front of and behind the axle unit, the low-bed section is angled for easier access, turntable with robust ball bearing race, foldable rear support, chocks, side impact protection, quarter-panel fenders
Lashing points: above the front axle: 2 pairs of ring lashing points, each 5 tons, at the front on the low-bed section / rear axle: 6 pairs of lashing points on the side in the low-bed section, each 8 tons. 6 pairs of lashing points, each 5 tons, between the longitudinal beams, a pair of pocket recesses embedded in the outer frame, internally 70 x 40 mm, or instead of pocket recesses, 5-ton ring lashing points embedded in the floor
Drawbar: tested 40 mm drawbar eye
Axles: BPW drum brake axles
Braking system: 2-line pneumatic braking system, spring-loaded parking brake, 2 non-interchangeable coupling heads at the front
Electrical system: 24 volts, multi-chamber lights, yellow side lighting, 2 white position lights at the front
2 white/red outline marker lights at the rear, rotating beacon with bracket, pair of illuminated and extendable warning signs up to 3,000 mm, 2 x 7-pole non-interchangeable connectors at the front
Floor: curved section at the front with steel/diamond-plate covering, storage compartment embedded in the access ramp to the curved section, driving lane area and in the center between the beams with steel/diamond-plate covering, rear slope with 70 mm softwood floor, low-bed platform including rear slope 5900 mm
Ramps: mounting rail for aluminum ramps over the entire width, as a U-profile over the entire width
Pair of aluminum ramps 800 mm long, approx. 400 mm wide, load capacity per pair 14,000 kg
Storage compartment for ramps between the beams
Approval: contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear
Lrsdpfx Aei Ri N Uslgen
Ilmoitus on käännetty automaattisesti. Käännösvirheitä saattaa esiintyä.
Toimittaja
Huomautus: Rekisteröidy ilmaiseksi tai kirjaudu sisään, saadaksesi kaikki tiedot.
Rekisteröitynyt vuodesta: 2006
190 Verkkoilmoitukset
Lähetä kysely
Puhelin & Faksi
+49 36482... ilmoitukset
Ilmoituksesi on poistettu onnistuneesti
Tapahtui virhe


























