Matala lavettipuoliperävaunu

MÜLLER-MITTELTAL 3- achs Sattel.-Luft-Lenk,hydr. Rampe mit Gummi

* TS 3 Profile 30.0:

----Brakes:

* Wabco EBS-E (electronic braking system)
* Emergency release device for spring-loaded cylinders
* Drum brakes

----Axles:

* 3 x 11 t BPW Eco Plus axles
* Last axle steered, with electro-pneumatic steering lock

----Suspension:

* Air suspension with lift and lower system and RtR valve

----Electrics / Lighting:

* TPMS (Tire Pressure Monitoring System)
* Smartboard control box mounted on the trailer as an info tool, with pressure sensors for total axle load display
* 15-pin electrical connector
* LED lighting system 12 / 24V
* Removable LED beacon, left rear

----General attachments:

* Side underrun protection
* Landing legs at the front and mechanical swivel supports at the rear of the chassis
* Straight steel mudguards
* Spare wheel carrier under the chassis, right side

----Low-loader deck:

* Saddle platform with 45° chamfered front corners and a front toolbox made of galvanized sheet steel, W = 2,480 x H = 500 x L = 665 mm, with folding lid
* 400 mm high drop-side aluminum boards (RAL 9010 pure white), foldable and removable, on the sides of the saddle platform
* Rear board – 150 mm high, slotted in
* Rear slope on the saddle platform to the low-bed section, approx. 700 mm long
* Saddle platform with 50 mm wooden planks and low bed with 60 mm wooden planks
* Tread plate over the axles

----Widening:

* 8 x mechanical folding extensions to 3 meters total width, not on the rear slope (widening planks available, stored on the saddle platform)
* Mechanically adjustable warning panel sets front and rear

----Load securing (Lasi package):

* On the saddle platform, 2 x 6.3 t lashing points each, as well as 3 x 5 t lashing bars each on the outside frame
* On the low-bed platform, 2 x 13.4 t lashing rings on each side, as well as 4 x 10 t lashing rings, pivotable and lowerable, integrated into the outside frame
* On each side, 2 x 6.4 t lashing eyes and one lashing point in the excavator arm trough at the rear
* 2 x container locks directly after the gooseneck in the low bed platform

----Excavator arm trough:

* Excavator arm trough starting from the end of the last fixed axle, over the steering axle up to the rear cross member, continuous with internal reinforcement profiles, approx. L = 2,450 x W = 770 mm x D = 270 mm

----Ramps:
Codpfx Aey Ngz Hsifsrb

* Mechanically operated one-piece, hot-dip galvanized hydraulic ramps, approx. 3,000 x 720 mm (mechanically adjustable in width)
* 4-way control block for later customer-side retrofit of hydraulic ramp shifting
* The outer board of the ramp is made of 50 mm hardwood
* Climbing strips on the outer frame of the ramp and on the approach slope
* Rubber mat on the ramp and approach slope

----Hydraulics:

* Hydraulic flow divider in the trailer (for hydraulic pump output in truck over 40 l up to 120 l/min)

----Load dimensions:

* Loading area of the saddle platform: approx. 3,935 x 2,480 mm
* Low-bed loading area: approx. 8,500 x 2,520 mm
* Loading height unladen about 910 mm (incl. 860 mm approach slope)

----Fifth wheel height:

* Approx. 1,220 mm (suitable for 2- and 3-axle tractors)

----Paintwork:

* Chassis, ramps, rear folding supports, widening consoles hot-dip galvanized
* Axles, landing legs, air tanks painted black
* Vehicle is hot-dip galvanized

----Info:

* New vehicle with manufacturer's warranty
* Errors and prior sale excepted
* Example images may show equipment not included with the offered vehicle
* Sample images

----Delivery time:

* tba

Ilmoitus on käännetty automaattisesti. Käännösvirheitä saattaa esiintyä.