Matala lavetti perävaunuMÜLLER-MITTELTAL
14,4 to, Tand - Plateau- Tieflader, hydr. Rampen
Matala lavetti perävaunu
MÜLLER-MITTELTAL
14,4 to, Tand - Plateau- Tieflader, hydr. Rampen
kiinteä hinta ei sisällä ALV
29 900 €
(35 581 € bruttomassa)
Valmistusvuosi
2025
Kunto
Uusi
Sijainti
Egestorf 

Näytä kuvat
Näytä kartta
Perustiedot
Hinta ja sijainti
kiinteä hinta ei sisällä ALV
29 900 €
(35 581 € bruttomassa)
- Myyjän sijainti:
- Eichenstich 12, 21272 Egestorf, Saksa

Soita
Tekniset tiedot
- Maksimi kuormauspaino:
- 10 800 kg
- Kokonaispaino:
- 14 400 kg
- Akselikokoonpano:
- 2 akselia
- Kuormatilan pituus:
- 6 270 mm
- Lastitilan leveys:
- 2 470 mm
Tarjouksen tiedot
- Listaustunnus:
- A204-85-575
- Viitenumero:
- 62471
- Päivitetty viimeksi:
- 21.01.2026
Kuvaus
* ETÜ-TA-R 14.4:
----Brakes:
* EBS brake system
* Emergency release device for spring brake cylinders
* Drum brakes
----Axles:
* 2 x 7 t Gigant axles
----Suspension:
* Parabolic springs with compensating unit
----Drawbar / Flange Drawbar Eye:
Duedpfsxvgrijx Ahxen
* Drawbar height-adjustable by 300 mm
* Drawbar extension by 250 mm to a total length of 2,250 mm
----Electrics / Lighting:
* Tire pressure monitoring with display option in the truck via EBS signal – without installation required on truck side
* 15-pin electrical connector
* LED lighting system 12 / 24 V
* EBS multi-voltage system for towing vehicles with 12 and 24 V electrics
----General Attachments:
* Front support winch
* External folding supports at the rear
* Plastic toolbox approx. 858 x 500 x 500 mm on the right front exterior of the front wall
* Side underrun protection
* Plastic quarter mudguards
----Low Loader Platform:
* 50 mm softwood floor
* Provision in front of the front wall for retrofitting container locks
* Bolted 400 mm smooth sheet front wall
* Bolted rear stanchions
* Drop sides with spring assists
----Load Securing:
* Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm
* Installation of 3 t recessed lashing rings possible every 600 mm
* In each front and rear corner, 1 x 6.3 t lashing point
* Various holes in the front and rear crossmember for 1.2 t lashing options
----Ramps:
* One-piece hydraulic grating drive-on ramps approx. 2,750 x 600 mm (can be pushed together to 20 mm clearance)
* Hydraulic flow divider in the trailer (for truck hydraulic output above 40 l/min up to max. 140 l/min)
----Paintwork:
* Chassis, drawbar, front wall, mechanical drop supports, and drive-on ramps hot-dip galvanized
* Axles, springs, air tanks, front support winch, and flange drawbar eye painted in a black tone
* Drop sides painted RAL 2011 deep orange
* Side panels available in a RAL color of your choice for an additional charge
----Information:
* New vehicle with manufacturer’s warranty
* Errors and prior sale excepted
----Delivery Time:
* Available immediately ex Egestorf
Mainos käännettiin automaattisesti ja käännösvirheet ovat mahdollisia.
----Brakes:
* EBS brake system
* Emergency release device for spring brake cylinders
* Drum brakes
----Axles:
* 2 x 7 t Gigant axles
----Suspension:
* Parabolic springs with compensating unit
----Drawbar / Flange Drawbar Eye:
Duedpfsxvgrijx Ahxen
* Drawbar height-adjustable by 300 mm
* Drawbar extension by 250 mm to a total length of 2,250 mm
----Electrics / Lighting:
* Tire pressure monitoring with display option in the truck via EBS signal – without installation required on truck side
* 15-pin electrical connector
* LED lighting system 12 / 24 V
* EBS multi-voltage system for towing vehicles with 12 and 24 V electrics
----General Attachments:
* Front support winch
* External folding supports at the rear
* Plastic toolbox approx. 858 x 500 x 500 mm on the right front exterior of the front wall
* Side underrun protection
* Plastic quarter mudguards
----Low Loader Platform:
* 50 mm softwood floor
* Provision in front of the front wall for retrofitting container locks
* Bolted 400 mm smooth sheet front wall
* Bolted rear stanchions
* Drop sides with spring assists
----Load Securing:
* Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm
* Installation of 3 t recessed lashing rings possible every 600 mm
* In each front and rear corner, 1 x 6.3 t lashing point
* Various holes in the front and rear crossmember for 1.2 t lashing options
----Ramps:
* One-piece hydraulic grating drive-on ramps approx. 2,750 x 600 mm (can be pushed together to 20 mm clearance)
* Hydraulic flow divider in the trailer (for truck hydraulic output above 40 l/min up to max. 140 l/min)
----Paintwork:
* Chassis, drawbar, front wall, mechanical drop supports, and drive-on ramps hot-dip galvanized
* Axles, springs, air tanks, front support winch, and flange drawbar eye painted in a black tone
* Drop sides painted RAL 2011 deep orange
* Side panels available in a RAL color of your choice for an additional charge
----Information:
* New vehicle with manufacturer’s warranty
* Errors and prior sale excepted
----Delivery Time:
* Available immediately ex Egestorf
Mainos käännettiin automaattisesti ja käännösvirheet ovat mahdollisia.
Toimittaja
Huomautus: Rekisteröidy ilmaiseksi tai kirjaudu sisään, saadaksesi kaikki tiedot.
Rekisteröity alkaen:: 2001
Lähetä pyyntö
Puhelin & Faksi
+49 40 33... ilmoitukset
Nämä ilmoitukset voivat myös kiinnostaa sinua.
Pieni ilmoitus
Egestorf
1 342 km
Työalustallinen perävaunu
MÜLLER-MITTELTAL14,4 to, Tand - Plateau- Tieflader, hydr. Rampen
MÜLLER-MITTELTAL14,4 to, Tand - Plateau- Tieflader, hydr. Rampen
Pieni ilmoitus
Egestorf
1 343 km
Matala lavetti perävaunu
MÜLLER-MITTELTAL14,4 to, Tand - Plateau- Tieflader, hydr. Rampen
MÜLLER-MITTELTAL14,4 to, Tand - Plateau- Tieflader, hydr. Rampen
Ilmoituksesi on poistettu onnistuneesti
Tapahtui virhe






























































