Avoin puoliperävaunu pressulla

KRONE SDP 27*Mega*SAF*LiftA*LenkA*StaplerH

VIN: WKESD00000891776

Distance from kingpin to center of support device: 2,267 mm
Fifth wheel height unladen: 980 mm
Double-T longitudinal and center beams as well as
cross beams and outriggers welded together
Outer frame with
Multilock outer frame, universal load securing option every 100 mm
Front height: 80 mm (incl. floor and fifth wheel plate)
2" kingpin (corner dimension: 2,040 mm)
Rear underrun protection device according to EC directive,
for cargo area length: 13,620 mm i.L.
for cargo area width 2,480 mm i.L.
3 axles, each with a load capacity of 9,000 kg
Aggregate distance = 7,900 mm
Wheelbase: 1,310 / 1,310 mm
with center alignment
BPW axles, 19.5", with air suspension (total travel 260 mm)
and disc brake (ET 120)
Brake disc with 370 mm diameter
Tire size 6-fold, 445/45 R 19.5
Tread depths
9/11mm
8/10mm
6/12mm
with lifting and lowering system, incl. automatic
ride height reset
load-dependent, fully automatic electronic
lift axle control for 1st axle
manual function on control console for forced lifting
Todpfx Ajzl Nzljlcob
(= starting aid according to Directive 97/27/EC) and forced lowering
Preparation of the lift/tag axle(s) for operation
from the tractor unit (without tractor unit installation),
according to the selected light connector(s),
for control via
Note: The vehicle does not operate in the
BO power circuit when the 1st axle is lifted! The lift axle may only be used as a starting aid according to
Directive 97/27/EC!
Attention: reduced ground clearance in the area of the lift axle!
Through-loading height is limited by pallet stop
Cargo area width in the area of the pallet stop
reduced to: 2,460 mm i.L.
Supply and installation of a rear forklift bracket, suitable
for Palfinger piggyback forklifts (incl. forklift pockets, underrun protection according to ECE-R58 and 2 chain retainers for securing chains on the outside)
Tire size piggyback forklift max.: 23"
Type of mounting bracket: spar bracket
Dimensions of the mounting spars: 100 x 100 x 10 x 1500 mm
Dimensions of the forklift pockets: 200x100x5x1200 mm
Center distance of the forklift pockets: 380 mm
Width of the folded underrun protection: 1340 mm
Forklift pockets flush with the end crossmember at the rear.
Socket at the rear: 15-pin DIN ISO 12098
uneven load distribution!
Type: BO 13620
30 mm thick, waterproof floor panel, cut surfaces
sealed all around, surface, waterproof bonding
between chassis and floor panel with permanently elastic high-performance adhesive. Strength according to DIN EN 283, for floor loads up to max. 7,000 kg forklift axle load.
Diamond plate inserted in floor panel at the rear (4x450mm)
Type: AB 13620 AGG Dimensions 13,620 mm iL. x Width iL.
see posts
LM universal outer beams, continuous, for mounting
sliding tarpaulin and sliding posts
Edscha sliding roof (175) with plastic joints,
building height 175 mm, inclination 0 mm, designed for the
transport of grid boxes according to DIN 15155
Height i.L. lower edge of outer beam on the side at the front: 2,860 mm
Height i.L. lower edge of outer beam on the side at the rear: 2,860 mm
Height i.L. lower edge of transverse spar in the middle: 3,000 mm
Through-loading height in the rear portal: 2,845 mm
unladen overall vehicle height at the highest point approx. 4095 mm
hydraulic lift roof with 500 mm total lift,
can be raised separately on 4 corner posts
Structure height at the front can be lowered by 150 mm from the highest driving height (basic position) (in 50 mm increments), reduced roof lift: 350 mm
Structure height

Ilmoitus on käännetty automaattisesti. Käännösvirheitä saattaa esiintyä.