Lavettitraileri

FLIEGL Tandem-Plattform-Anhänger TPS 210 Jumbo

Custom-Made Transport Solution
Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications.

Chassis: Center-Axle Trailer
Fine-grained steel welded construction
2-speed gear-supported landing leg at the front
Folding rear support
Guodjzcvt Ropfx Apcjc
2 jockey legs with holder
Aluminum side impact protection
Splash flaps at the rear, spanning the entire width
Quarter panel fenders in front of and behind each axle
with anti-spray splash flaps according to EC regulations
1 aluminum storage box with stainless steel flap
Container locking mechanism, 1 pair of recessed locking recesses in the floor for 1 x 20 ft container, 1 pair of container locking adapters
Extendable widening sections to 3,000 mm
Storage compartment for wooden planks in the center + wooden planks 70 mm for widening to 3000 mm
Tie-down points, low-bed trailer
1 pair of tie-down brackets additionally at the front in the front cross member, 10 tons each
5 pairs of ring tie-down points recessed in the outer frame, 5 tons each (can be converted to stake pockets)
7 pairs of tie-down cleats recessed on top and on the side in the outer frame, 10 tons each
Coupling system, center-axle trailer
Drawbar with tested 50 mm tow hitch
Axles + Suspension
Drum brake axles, according to the manufacturer's choice
"Axle/chassis laser aligned" reduces tire wear and fuel consumption
Axle distance 1810 mm
Air suspension
Braking system
2-line compressed air braking system
Color-coded line routing for easy servicing
Spring-loaded parking brake
2 fail-safe coupling heads at the front, with connection lines to the towing vehicle
Parking sockets for ABS/EBS and air connection on the drawbar or drawbar
24 Volt EBS, electronic braking system with EBS connector at the front
with lift and lower valve
Vehicle - driving stability system
Axle load recognition via EBS-CAN bus signal, for display on the display in the cab
"TPMS" Tire Pressure Monitoring System according to ECE R 141, display on the display in the towing vehicle, via EBS
Wheels and Tires
235/75 R17.5, manufacturer's choice
Protective caps for wheel studs
Electrical System
24 Volt, multi-chamber lights in LED, yellow LED lighting on the side, license plate lighting in LED
Yellow LED lighting on the side, coupled with the turn signal "Flashing side marker lights"
Premium LED side marker lights, with "20 LED diodes per light"
2 white position lights at the front in LED
2 white/red outline lights at the rear in LED
2 x 7-pole fail-safe plugs at the front, with connection cable
Parking sockets for electrical system on the drawbar
LED work lights on both sides
2 additional LED work lights at the rear
1 LED rotating beacon with holder, switched via sidelights
2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm
Floor
thereafter with approx. 70 mm soft wood flooring, in the wheel arch area steel/diamond plate flooring
Rear inclination with "Mega Grip surface" made of interlocking grating
Low-bed area including rear inclination 6,500 mm
Front panel / corner posts
Aluminum profile, approx. 400 mm high, plug-in
Ramps
Steel ramps 2,800 mm long, 750 mm wide, laterally movable
Ramp surface with "Mega Grip" made of interlocking grating
Hydraulically operated via towing vehicle auxiliary drive with throttle, operation on the left side
Hydraulic side displacement of the ramps, individually controllable
Hydraulic connection with quick-release cou

Ilmoitus on käännetty automaattisesti. Käännösvirheitä saattaa esiintyä.