Matala lavetti perävaunu

Fliegl Tiefladeanhänger DTS 300 L=6,5 m Luft/FH

Low-bed trailer chassis: Steel welded construction, turntable with robust ball bearing, foldable rear support, 2 chocks with holder, aluminum side impact protection, splash guards at the rear covering the entire width (not in conjunction with forklift mount), half-shell wheel arches, 1st axle with anti-spray splash guard, anti-spray splash guards behind the 2nd and 3rd axles, 1 plastic toolbox with insert, w=620/h=360/d=440 mm, lockable with a padlock, extendable widening sections to 3,000 mm, storage compartment for wooden planks in the center of the loading area, 70 mm wooden planks for widening to 3,000 mm, lashing points for low-bed trailers, 1 pair of lashing recesses in the front longitudinal beam, recessed in the flange, 10 tons each, 4 pairs of lashing holes in the outer frame, 5 tons each (for strap attachment), 7 pairs of lashing eyes recessed in the top and side of the outer frame, 10 tons each, 1 at the front in the flange, 6 in the low bed, the first lashing point 250 mm from the front and the last max. 250 mm from the rear, distance between lashing points not greater than 1100 mm, 5 pairs of ring lashing points recessed in the outer frame, 5 tons each (convertible to pocket lashing points), 2 pairs of folding lashing points additionally, 10 tons each, 1 on the flange (protruding), 1 behind the last axle recessed in the floor, 1 pair of screw lashing points, 6.7 tons each (JDT), with large flange plate including thread as counter-holder, at the front on the flange.
Trailer turntable hitch: Drawbar with tested 40 mm drawbar eye, parking sockets for electrical/ABS and air connections on the drawbar.
Axles + Suspension: SAF drum brake axles, "axle/chassis laser-measured" to reduce tire wear and fuel consumption, air suspension with lift and lower valve, operable separately at the front and rear.
Wheels and Tires: 235 / 75 R 17.5", Fulda, rims: 6 x steel rims in twin arrangement, mounted on the inside; 6 x aluminum rims, polished, mounted on the outside.
Braking System: 2-line compressed air braking system, spring brake parking brake, Trailer Info Center for displaying vehicle data such as axle load (not an approved scale) and odometer, vehicle stability system, axle load detection via EBS-Canbus signal for display on the dashboard in the cab, truck must be appropriately pre-equipped, 2 non-interchangeable coupling heads at the front, with connection lines to the tractor unit, EBS, electronic braking system with EBS plug at the front, with connection cable.
Bsdpfxezaznze Amxjdc
Electrical System: 24 Volt, multi-chamber lights in LED, yellow LED lighting on the sides, license plate lighting in LED, manufacturer Aspöck EcoLED 2 with dynamic turn signal, premium LED side marker lights, 2 white position lights at the front in LED, 2 white/red marker lights at the rear in LED, 2 x 7-pole non-interchangeable plugs at the front, with connection cable, additional LED work light at the rear, 1 LED rotating beacon with holder, switched via parking lights, 2 pairs of warning signs, LED-illuminated and extendable to 3,000 mm.
Floor: Front flange with steel/diamond plate covering, storage box recessed in the ramp to the flange, followed by a 70 mm larch wood floor, steel/diamond plate covering in the wheel arch area, rear slope with 70 mm larch wood floor, low-bed area including rear slope 6,500 mm, loading ramps, steel ramps 2,800 mm long, 750 mm wide, laterally displaceable, additional ramp locking device, foldable at the bottom (to prevent lateral slippage o

Ilmoitus on käännetty automaattisesti. Käännösvirheitä saattaa esiintyä.