Matala puoliperävaunu rakennuskoneiden kuljetukseen

Faymonville 4-(1+3)-A-Tele-Semi-Radm.-Rampen-Gummib.

Gooseneck:
- Gooseneck in SNT design to optimize loading deck length, length approx. 3,700 mm
- Gooseneck rear with chamfer, approx. 1,000 mm x 10°
- For tractor units: 6x2, 6x4, short 8x4

Loading platform:
- Loading platform in extendable version, length approx. 8,800 mm, with rear chamfer approx. 500 mm x 10°
- A recess in the deck and chamfer to accommodate the excavator bucket stick, approx. 3,850 x 750 x 210/290 mm

Two-piece steel ramps:
- A pair of two-piece steel ramps, each approx. 4,350 mm long and 900 mm wide
- Ramps with rubber lining
- Hydraulically foldable ramp tips
- Ramps can be hydraulically adjusted individually approx. 235 mm outward and approx. 215 mm inward
- "Super Grip" rubber flooring 25 mm and steel plate approx. 5 mm as additional reinforcement on the rear chamfer of the loading area
- Square climbing strips 20 x 30 mm, approx. every 200 mm on the outside frame of the ramp

Axles, Suspension, and Tyres:
- BPW axles and suspension, 1st axle is force-steered, all other axles hydromechanically forced-steered
- Technical axle load: 12,000 kg
- 1st axle with electromagnetic reverse lock, can be activated via reverse gear and manually
- Air suspension with raise and lower valve
- Tyres 235/75 R 17.5
- TPMS tire monitoring system

Accessories included:
- Plug-in steel front wall, approx. 400 mm high
- Yellow-red air couplings on the front connection plate
- 3 kW electro-hydraulic unit for operating hydraulic functions
- 1 spare wheel
Lhodpfx Ageywizfj Ijd
- Outer beams from gooseneck with mounting holes for screwable lashing rings
- First hole approx. 200 mm from front, then approx. every 400 mm
- 2 pairs screw-in lashing rings included
- 1 pair horizontal lashing rings in the rear section of the gooseneck
- On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized
- On the gooseneck, a plug-in ALU tailboard, approx. 400 mm high, anodized
- Gooseneck equipped with approx. 40 mm hardwood floor covering, over the kingpin with checker plate cover
- 2" kingpin
- NATO round socket on the front connection plate
- 4 chocks
- Mechanical landing gear
- Loading platform with continuous and between-axle interrupted approx. 50 mm thick hardwood floor
- Locking of the loading platform with conically welded-on locking profiles every 250 mm
- Includes pre-tension plate
- 1 intermediate table, approx. 300 mm wide
- 1 pair lashing rings on the front cross member
- 8 pairs of recessed, folding-out lashing rings in the outer frame of the loading platform
- Extendable (galvanized) outriggers per side approx. 230 mm
- Wheel recesses with square climbing strips, 15 x 15 mm, open continuously in front of the axles up to the cross member of the gooseneck, approx. 700 x 410 mm
- Lockable aluminium elements on the extension tubes of the outriggers
- Widenable U-profiles for inserting ALU covers
- Wheel recesses with square climbing strips, 15 x 15 mm between the 1st and 2nd axle, approx. 1,480 x 700 x 410 mm
- ALU covers for the wheel recesses
- Lockable aluminium elements on the extension tubes of the outriggers
- 1 pair of mechanical rear supports
- Radio and cable remote control
- Lift axle on the front axle
- Square climbing strips 20 x 30 mm
- Central lubrication system
- Wabco Smart Board system
- 4 warning boards, approx. 423 x 423 mm, extendable

Ilmoitus on käännetty automaattisesti. Käännösvirheitä saattaa esiintyä.