Matala lavetti perävaunu

MÜLLER-MITTELTAL 4-achs Anh. Tieflader, Klapprampe, Gummibelag

T 4 Profi 40.0

----Brakes:

* Wabco EBS-E (electronic braking system)
* Emergency release device for spring brake cylinders
* Drum brakes

----Axles:

* 4 x 11 t Gigant axles

----Suspension:

* Air suspension with lifting and lowering function and RtR valve

----Drawbar:

* Straight drawbar with 50 mm towing eye and stepless height adjustment

----Electrics / Lighting:

* Tire pressure monitoring system with display capability in the truck dashboard via EBS signal – no installation required on the truck side
* SmartBoard as an infotool with pressure sensors for axle load display by axle group
Ihodeylfvgepfx Ahxju
* 15-pin power connector
* LED tail lights
* LED beacon (removable) at rear

----General Attachments:

* Warning sign packages front & rear
* 2 x toolboxes made of galvanized and powder-coated sheet steel approx. 650 x 300 x 600 mm, mounted on right side
* Enclosed single plastic mudguards at the front
* Straight rear steel mud aprons, each with spray protection (spray suppression)
* Side underrun protection

----Low Loader Platform:

* Gooseneck platform extended by 520 mm with 45° corners and 3 integrated storage compartments incl. lockable lids
* Flooring above gooseneck platform: 50 mm; in low bed: 60 mm softwood
* 20 mm rubber covering instead of wooden floor in running area, with a depressed bed length of 6,780 mm including the drive-on slope
* Rubber covering on the drive-on slope left and right approx. 860 mm long
* 4 stake pockets per side (stakes not included), each with 2 t lashing capacity

----Chassis:

* Chassis made of high-tensile fine-grained steel

----Load Securing (Lasi Package):

Gooseneck Platform:
* 2 pairs of 13.4 t lashing rings in the outer frame

Low Bed:
* 4 pairs of 10 t folding lashing rings per side on the outer frame, loadable in all directions
* 2 pairs of 13.4 t swiveling lashing rings per side at the rear

----Ramps:

* Rubber covering on the folding drive-on ramps
* Hydraulic folding ramps with hydraulically extendable end section, approx. 4,650 x 720 mm
* Hydraulic lateral ramp adjustment and load-holding valves

----Rear Support:

* Hydraulic rear support

----Widenings:

* 8 pairs of galvanized folding outriggers for 3 m total width (not in the rear slope area)
* Extension boards stored on the left side in a storage compartment

----Excavator Arm Tray:

* Excavator arm tray above the rear axle up to the end of the drive-on slope approx. L=2,100 mm x W=740 x D=190 mm
* 2 pairs of 6.4 t lashing rings per side in the excavator arm tray

----Hydraulics:

* Hydraulic flow divider in the trailer (for hydraulic pump capacity in truck over 40 up to max. 120 l/min)

----Loading Dimensions:

* Rear loading area: approx. 6,780 x 2,520 mm (incl. 860 mm drive-on slope)
* Loading area above the turntable: approx. 2,990 x 2,520 mm

----Loading Height:

* Loaded approx. 890 mm, +/- 20 mm

----Paintwork:

* Reflective contour tape on sides and rear
* Chassis, gooseneck, drive-on ramps, and folding outriggers hot-dip galvanized
* Axles, drawbar, air tanks, and turntable painted in a black tone

----Information:

* New vehicle with manufacturer’s warranty
* Errors and prior sale excepted
* Example images may include special equipment

----Delivery Time:

* Vehicle available from approx. calendar week 23/2026

Mainos käännettiin automaattisesti ja käännösvirheet ovat mahdollisia.