Matala lavettipuoliperävaunu

MEUSBURGER MTS-4 Ausziehbar 13400 - 18000 mm 2 x Lenk Tüv

Technical Data Trailer:

First registration: 27.10.2020
Length: 13,400 mm – 18,000 mm
Year of manufacture: 2020
Width: 2,550 mm
Perm. total weight: 58,000 kg
Height: 2,540 m
Unladen weight: 10.6 t
Number of axles: 4
Main inspection (HU): 11/2026
Axle spacing: 1310 mm / 1310 mm / 1310 mm

Trailer Equipment:

Chassis
- Robust steel frame welded construction with front frame cranking and flat low-bed platform, rear chamfer 500 x 100 mm
- Neck of frame: 110 mm
- 8 mm fifth wheel plate with interchangeable 2" king pin
- Front corners chamfered 400 x 400 mm
- No winch slope on cranked platform
- Frame neck with none or only slight pre-tension (for container transport)
- Low-bed with extendable central frame, extension length approx. 4,300 mm, each 500 mm or 1x 300 mm pneumatically, additional locking positions of the extension at 250 mm and 750 mm telescoped
- No wheel recesses
Kwodpfx Abjycnc Dsget
- Intermediate table, 300 mm long, supports before and after division shortened and without spring latch
- Outer frame as perforated side frame/40 mm diameter, delivered as with 3-axle models with factory no. 12668ff
- No excavator trough
- Reinforced frame design for point load 40 t over 5 m in retracted state at center of gravity
- Reinforced rear end, drive-over capacity 40 t
- Underrun protection = extended end plate
- Hanging rail at rear end plate
- Rear drop supports
- Slide protection at end plate due to low ground clearance for ship loading, either higher slide protection or, if possible, storage compartment for ramps designed lower

Support Legs
- Front drop supports

Axles
- BPW air suspension axles, each with 10 t axle load, airbag diameter 360 mm
- S-cam brake 300/200 mm, asbestos-free brake pads
- Automatic slack adjusters
- Wabco SmartBoard with ECAS function with lift/lowering device, total lift approx. 200 mm
- 2 additional ride height levels: + approx. 40 mm or – approx. 40 mm from standard position
- 1st axle as lift axle (via SmartBoard), operation electric via buttons on trailer and in cab (without cab wiring)
- When lift axle is activated, ride height changes to 900 mm platform height, ground clearance approx. 60 mm under lifted axle
- Ride height increase +40 mm (i.e. approx. 940 mm) when axle is lifted
- No hubodometer (read via SmartBoard)
- No axle load gauge (read via SmartBoard)

Steering
- 3rd and 4th axles as friction-steered trailing axles with mechanical and electric lock (via reverse gear) and automatic steering lock on 3rd axle when lift axle is raised

Lubrication System
- Central lubrication system with pump and timer for all lubrication points on axles, make BekaMax

Rims and Tires
- 18 Alcoa "DuraBright" aluminum wheels, 10-hole, with offset, center mounting
- "Air-Flexx" valve extension as supplied for factory no. 11918 - longer
- 18 tires 245/70 R 17.5 143/141 J, tubeless
- Make: Michelin XTE2

Mudguards
- Aluminum plate mudguards with clear pass

Brake System
- Two-line brake with EBS
- EBS (WABCO 4S3M)
- Spring-loaded parking brake
- Without connecting hoses/cables to truck

Electrical Equipment
- As per motor vehicle regulations
- 24 volts. 2x 7-pin sockets
- 2 pcs. 7-chamber tail lights in end plate (LED)
- Side marking lights LED
- 1 LED warning beacon at rear
- Front and rear position lights LED
- 2 pcs. Schuko sockets (220 V) at left and right sides of end plate for overhang lighting (no lighting supplied) (only + and – poles marked for lighting)
- 2 additional recessed reversing lights in rear end plate
- No connecting ca

Mainos käännettiin automaattisesti ja käännösvirheet ovat mahdollisia.