Matala lavettipuoliperävaunu

FAYMONVILLE MAX Trailer MAX110 Semi-Tieflader

You can find our complete range of vehicles, including those available for immediate delivery or on short notice, on our website.

Below is an excerpt from the specification. The full equipment list is available upon request.

Gooseneck:
* Gooseneck with front corners chamfered approx. 45° and a rear bevel approx. 750 mm x 10°
* 3 pairs of lashing rings (LC 5,000 daN)
* Hardwood flooring approx. 30 mm thick

Load area:
* Double extendable design with rear bevel approx. 500 mm x 8°
* 6 pairs of folding external lashing rings (LC 5,000 daN)
* 4 pairs of folding external lashing rings (LC 10,000 daN)
* 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN)
* 1 intermediate table approx. 250 mm
* Hardwood flooring approx. 48 mm thick, over axles with checker plate covering
* Cut-outs in the external frame of the loading platform for attaching tie-down straps (LC 2,000 daN)

Axles:
* BPW axles and suspension, all axles forced-steered hydro-mechanically
* Design axle load: 12,000 kg each
* Air suspension with lift and lower valve
* Axle tools included

Tyres:
* 245/70 R 17.5, load index (146/146 F)
* Brand of our choice

Landing legs:
Fpsdjw Tprzepfx Aifsg
* JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load)

Braking system:
* Braking system according to EU regulations with EBS-E (2S2M) without connection lines to the tractor unit

Paintwork:
First-class and durable corrosion protection
* High-quality, one-colour 2-component (2K) topcoat in RAL 3002 carmine red
* Rear section metallized and coated in RAL 9010 (pure white)

Steel Structure:
Steel construction from high-strength fine grain steels.
* Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa)

Electrical system:
* Electrical system according to EU regulations
* 24 Volt lighting ASPÖCK-NORDIK (ASS3)
* ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets, compliant with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098

Including the following additional equipment:
* 2-inch kingpin
* Galvanized steel front wall, approx. 400 mm high
* Yellow-red air couplings at the galvanized front connection strip
* Spare wheel carrier in front of the front wall
* Electro-hydraulic unit
* Rear and front steering via cable remote control with push-buttons, with single-track monitoring of the axles (without installation in the tractor unit)
* Mount at the rear of the gooseneck for aluminum loading ramps
* Removable aluminum ramp hanging rail at the rear of the vehicle
* Galvanized folding supports beneath the slope of the load area
* On the gooseneck: plug-in aluminum side boards and rear board, approx. 2,440 x 400 mm (L x H)
* The rear galvanized stanchions are removable (body length approx. 2,560 mm)
* One galvanized toolbox, integrated in the chamfered gooseneck
* 4 pairs of WADER container pockets in the loading area for one 20', two 20', one 40' or one 45' container
* 8 pairs of stanchion pockets (approx. 100 x 50 mm) in the external frame of the loading platform
* Galvanized extensions, extendable by approx. 230 mm per side
* Adjustable hanging rails for aluminum ramps at the rear of the vehicle
* 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear
* Central lubrication system with 2 BEKAMAX (Pico) pumps, filled with standard grease NLGI-2 and removable pump guard
* 2 LED reversing lights mounted on the rear panel
* HRM Metallization (High Resistance Metallisa

Ilmoitus on käännetty automaattisesti. Käännösvirheitä saattaa esiintyä.