Matala lavetti perävaunu

FLIEGL DTS 300 3-Achs Tiefl 6,5m Parab Hydraulik

From ongoing production

Total weight: 24,000kg/ 30,000kg
Empty weight: 6,100kg
Payload: 17,900kg/ 23,900kg
Total length: 10,890mm
Loading length: 8,670mm total, 2,520mm offset, 6,500mm loading bed
Width: 2,520mm
Loading height: 860mm
Further information
Steel welded construction
Turntable with strong ball bearing ring
Foldable rear support
Bjdpouytx Ssfx Aaxslp
Wheel chocks with holder
Aluminum side impact protection
Rear mud flaps across the entire width (not in conjunction with forklift bracket)
Half-shell mudguard 1st axle with anti-spray mud flaps
Anti-spray mud flaps behind 2nd and 3rd axles
Plastic tool box
Extendable extensions to 3,000mm
Storage compartment for wooden planks in the middle of the loading area
Wooden planks 70 mm for widening to 3,000 mm
Lashing eyes for low loader
1 pair of lashing cutouts in the longitudinal beam at the front on the offset, 10 tons each.
4 pairs of lashing holes in the outer frame of the crank, each with 5 tons (tension belt attachment)
7 pairs of lashing mushrooms embedded in the outer frame at the top and side, each with 10 tons
1 x at the front on the crank, 6 x in the low bed
Pair of ring lashing eyes embedded in the outer frame, each with 5 tons (can be converted to stake pockets)
Pair of additional folding lashing eyes, each with 10 tons
1 x on the crank
1 x embedded in the floor behind the last axle
Trailer towing device, turntable
Draw fork with tested 40 mm drawbar eye
Draw fork height adjustment via spring
Axles + suspension
Drum brake axles, at the manufacturer's discretion
"Axles/chassis laser-measured" Reduction in tire wear and fuel consumption
Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation
(rocker compensation)
Wheels and tires
235 / 75 R 17.5"
at the manufacturer's choice
steel rims in twin arrangement, factory silver
brake system
2-line compressed air brake system
spring-loaded parking brake
2 interchangeable coupling heads at the front, with connecting lines to the motor vehicle,
24 volt ABS and ALB, with ABS plug at the front, with connecting cable
electrics
24 volt, multi-chamber lights, yellow LED lighting on the side
2 white position lights at the front
2 white/red lane keeping lights at the rear
2 x 7-pin interchangeable plugs at the front, with connecting cable,
LED rotating beacon with holder, switched via parking light (light removable)
pair of warning signs with double LED lighting and extendable to 3,000mm
floor
front bend with steel/checker plate covering
storage box embedded in the crossing slope to the bend
then with approx. 70mm softwood floor, in the wheel arch area steel/checker plate covering
rear bevel with 70mm softwood floor
Low loading area including rear bevel 6,500mm
Loading ramps
Steel ramps 2,800mm long, 750mm wide, can be moved sideways
Additional ramp lock foldable at the bottom (to prevent the ramps from slipping sideways, not in conjunction with
lateral hydraulic ramp shifting)
Covered with wood (tip area with steel/checker plate)
Hydraulic via tractor auxiliary drive with throttle, actuation on the side in FR left
Hydraulic connection with SVK plug NW 10/3, including connecting hose
Paintwork
Frame hot-dip galvanized including passivation
Loading ramps hot-dip galvanized
Plus pre-freight / provision from storage location 26639 Wiesmoor 1,280.00 €/ net

Mainos käännettiin automaattisesti ja käännösvirheet ovat mahdollisia.